picai
 

 

 

 

IC-prog

 

   Su šia programa galima įkelti *.hex tipo failus per programatorių į mikrovaldiklį. Programa suderinta su šiais programatoriais:

  • DM Programmer (Ludipipo),

  • Conquest programmer,

  • TAFE Programmer,

  • TAIT 'Classic' Programmer,

  • Parallel TAIT programmer,

  • Fun-card Programmer,

  • SCHAER Programmer,

  • ProPic II Programmer,

  • STK200 Programmer,

  • AN589 Programmer,

  • WILLEPRO Programmer,

  • Fluffy2 Programmer,

  • DL2TM Programmer,

  • ER1400 Programmer

Programa leidžia dirbti su šiais mikrovaldikliais:

PIC16F818, 16F819, 16F630, 16F676, PIC18F1320, PIC18F6620, 18F242, 18F248, 18F252, 18F258, 18F442, 18F448, 18F452, 18F458, 12C508, 16C84, 16F84, 16F877, 16F74, 24C16, 24C32, 93C46, 90S1200, 59C11, 89C2051, 89S53, 250x0, PIC, AVR , 80C51 ir t.t.

 

Programos reikalavimai:

min. 8Mb RAM ir CPU 386

 

 

NUSTATYMAI

 

Settings for JDM Programmer:

You need the following settings in IC-Prog:

 

 

Settings for Multiprog98

You need the following settings in IC-Prog:

 

 

You also need to set some jumpers correctly for SCHAER:

 

Jumper

Position

J1

1-2

J2

1-2

J3

2-3

J4

1-2

J5

3-4

J6

7-8

J7

1-2

 

Here are the jumper positions for PHOENIX: (Requires serial port)

 

Jumper

Position

J1

2-3

J2

2-3

J3

2-3

J4

1-2

J5

3-4

J6

3-4

J7 + J8

3-4

 

Settings for MK13 Programmer 

You need the following settings in IC-Prog:

 

 

 You also need to set some jumpers correctly:

Switch

Position

1

OFF

2

ON

3

OFF

4

OFF

 

Jumper 1 on the top of the programmer needs to be shorted
Jumper 2 on PCB must be shorted.
Switch 5 (single switch near the power socket) must be pointing towards the power socket.
Switch 6 (single switch near the 8 pin osc) must be pointing away from the power socket.
 

Settings for SI Prog

You need the following settings in IC-Prog:

 

 

 If you are going to use the SI Prog for PIC's then you need to INVERT Data Out!

 

Settings for Multi-3 Programmer

 You need the following settings in IC-Prog:

 

 

Settings for Multi Pro Programmer

 You need the following settings in IC-Prog:

 

 

Settings for PicLink Programmer

 You need the following settings in IC-Prog:

 

 

Settings for Z-Programmer

 You need the following settings in IC-Prog:

 

 

Settings for Conquest Programmer

You need the following settings in IC-Prog:

 

 

Settings for WILLEPRO Programmer

You need the following settings in IC-Prog for programming PIC's:

 

 

For programming Microwire devices (93Cxx) and 4-wire devices (59C11) you need the following settings:

 

 

IC-Prog only supports Microwire and 4-wire in 16 bits mode. Therefore pin 6 (ORG) of this socket, needs to be DISconnected from GND and CONNECTED to VCC!!!

For programming SPI-Eeproms (25xxx) you need the following settings:

 

 

Settings for MiniPico Programmer

You need the following settings in IC-Prog:

 

 

Settings for Maxking 12C508 Programmer

You need the following settings in IC-Prog:

 

 

Settings for KIT96 and KIT119 Programmer

You need the following settings in IC-Prog:

 

  
 
   

© MrFreeTemplates.com 2004